Titanium Forgings WeChat/WhatsApp：+86 17899176524

Six Factors Affecting Metal Flow During Extrusion Of Titanium Alloy Materials

titanium rods and titanium alloy rod blanks have low thermal conductivity, which will cause a great temperature difference between the surface layer and the inner layer during hot extrusion. When the temperature of the extrusion cylinder is 400 degrees, the temperature difference can reach 200 to 250 degrees. Under the combined influence of suction strengthening and the large temperature difference of the blank section, the metal on the surface and the center of the blank produces very different strength and plastic properties, which will cause very uneven deformation during the extrusion process. Large additional tensile stress is generated in the extruded product, which becomes the source of cracks and cracks on the surface of the extruded product. The hot extrusion process of titanium rods and titanium alloy rod products is more complicated than the extrusion process of aluminum alloy, copper alloy, and even steel, which is determined by the special physical and chemical properties of titanium rods and titanium alloy rods.Industrial titanium alloy metal flow kinetics research shows that in the temperature zone corresponding to the different phase states of each alloy, the metal flow behavior is greatly different. Therefore, one of the main factors affecting the extrusion flow characteristics of titanium rods and titanium alloy rods is the heating temperature of the blank that determines the state of the metal phase transformation. Extrusion at the temperature of a or a+P phase zone is more uniform than extrusion at the temperature of p phase zone. It is very difficult to obtain high surface quality for extruded products. So far, the extrusion process of titanium alloy rods must use lubricants. The main reason is that titanium will form a fusible eutectic with iron-based or nickel-based alloy mold materials at temperatures of 980 degrees and 1030 degrees, which will cause the mold to wear strongly.The main factors affecting metal flow during extrusion:1) Extrusion method. Reverse extrusion is more uniform than forward extrusion, cold extrusion is more uniform than hot extrusion, and lubricated extrusion is more uniform than non-lubricated extrusion. The influence of the extrusion method is realized by changing the friction conditions.2) Extrusion speed. As the extrusion speed increases, the unevenness of metal flow increases.3) Extrusion temperature. When the extrusion temperature increases and the deformation resistance of the blank decreases, the uneven flow of the metal increases. During the extrusion process, if the heating temperature of the extrusion cylinder and the mold is too low, and the metal temperature difference between the outer layer and the center layer is large, the unevenness of the metal flow will increase. The better the thermal conductivity of the metal, the more uniform the temperature distribution on the end surface of the ingot.4) Metal strength. When other conditions are the same, the higher the metal strength, the more uniform the metal flow.5) Modular angle. The larger the die angle "(that is, the angle between the end face of the die and the central axis), the more uneven the metal fluidity. When using porous die extrusion, the die hole arrangement is reasonable, and the metal flow tends to be uniform.6) Deformation degree. If the degree of deformation is too large or too small, the metal will flow unevenly.

#titaniumbar #titaniumbars #titaniumbarfactory #titaniumbarsupplier #titaniumbarmanufacturer #titaniumrod #titaniumrods #titaniumrodsupplier #grade5titaniumbar #medicaltitanium https://www.cynfm.com/titanium-bar-rod/titanium-bar-for-aerospace.html（在 Mayingchen, Shaanxi, China） https://www.instagram.com/p/CcrZ5KduDFQ/?igshid=NGJjMDIxMWI=

Chenyuan metal, which is mainly engaged in titanium rod and titanium all...

Gr5 / TC4 titanium alloy wire for Cutting EPS blockWire thickness: 1mmMelting point:1600 degrees CelsiusTensile strength:1300~1500Nhttps://www.cynfm.com/titanium-wire/●Gr5 / TC4 Thermal expansion coefficient:Gr5 / TC4 titanium alloy has a series of advantages such as excellent corrosion resistance, small density, high specific strength, better toughness and weldability, etc., and has been successful in aerospace, petrochemical, shipbuilding, automotive, medicine and other sectors. Applications.●Gr5 / TC4 titanium alloy density:4.5 (g/cm3)●Gr5 / TC4 titanium alloy chemical composition:Gr5 / TC4 contains titanium (Ti) balance, iron (Fe) ≤ 0.30, carbon (C) ≤ 0.10, nitrogen  ≤ 0.05, hydrogen (H) ≤ 0.015, oxygen (O) ≤ 0.20, aluminum (Al) 5.5～6.8, Vanadium (V) 3.5～4.5 [1-2]●Working temperature -100～550 (℃)#titaniumalloywire #tc4titaniumwire #Gr5titaniumwire #ti6al4vwire#titaniumwire

Titanium block （在 Baoji） https://www.instagram.com/p/CPSn2fkhGBj/?utm_medium=tumblr

grade 5 titanium welding wire pickled titanium wire titanium alloy wire titanium welding wire http://m.cynfm.com/titanium-wire/ https://www.instagram.com/p/CL59lWihXge/?igshid=1a1y1g2asmpzx

Titanium flange processing #Titanium flange（在 Mayingchen, Shaanxi, China） https://www.instagram.com/p/CR3E3knrtTa/?utm_medium=tumblr

Titanium alloy upsetting and forging 

Baoji Chenyuan Metal Material Co., Ltd. titanium bar titanium forgings Sputtering target arya@cynfm.com www.cynfm.com +86 17899176524

titanium bar titanium forgings Sputtering target Baoji Chenyuan Metal Ma...

#titaniumforgingsgrade5 #titaniumforging #titaniumforgings #titaniumforgedring #titaniumforgedparts #titaniumforged #titaniumforgingdisc #titaniumforgingdisc https://www.cynfm.com/titanium-forgings/ti-forged-block/titanium-alloy-block.html（在 Baoji） https://www.instagram.com/p/CZ8O_fKLo4N/?utm_medium=tumblr